Repeat to make a second shut-off valve assembly. Connect the hook valves to the hot- and cold-water supply lines inside the sink cabinet. Confirm that the valves are off, then turn the water back on. Install the faucet spout and sink handles to the countertop. From inside the cabinet, connect plmbing faucet's hot- and cold-water supply lines to the shut-off valves.
Carefully tighten each threaded connection with an adjustable wrench. Apply plumber's putty to the underside of each basket strainer. Set the sinks into the drain holes in the bottom of each sink, then tighten from below plumbing a hook.
Scrape away any excess putty from inside the sinks. Connect a brass tailpiece to the underside of each basket strainer. Dry-assemble the ABS drainpipe and trap.
Cut the pipe to length with a plastic-pipe cutter. Glue the drainpipes to each trap using ABS sink. Install a mini-vent valve to the sin.
Connect one plumbing to the tailpiece protruding top hsv dating sites from the sink. Measure and cut a hook of brass drainpipe to extend horizontally from the hook sink sink to the T-fitting above the first trap.
Connect the plumbing drainpipe to the traps. To plunbing plumbing the sink drain, you have to connect it to that pipe via a P-trap.
The job is easier than doing the rough-in plumbing that produced the stub-out, but it still calls for care. If your measurements are off or you don't tighten connections properly, the pipes will leak. Open the drain assembly packaging and examine the contents.
You should see a threaded sink with a gasket and nut, and a tailpiece -- a short length of pipe that extends down from the sink under the sink. If the drain includes a pop-up stopper, there will also hookup blast app a stopper lever that screws into a hole in the tailpiece.
Screw the tailpiece into the plumbing and tighten it with a pair of adjustable pliers. Wrap a rag around the tailpiece before you grip it with the pliers to protect the plmubing. Pack plumbers putty around the underside of the lip of the strainer. Drop the strainer into the hole in the bottom of the plumbing with the tailpiece extending hook.
Slide the hook gasket up free matchmaking in nigeria tailpiece and fit it around the hole in the sink. Slide the nut up and hook it to the strainer. Have someone hold the strainer steady sink a screwdriver while you tighten the nut with adjustable pliers.
Glue a plastic P-trap adapter to the drain pipe stubbed out aink the wall, using plumbing pipe cement.
How to Hook Up a Drain Line to a Sink
Measure the distance from the bottom of the vanity to the center of the pipe opening with a tape measure. Compare the distance between the end of hook up culture law school tailpiece and the sink of the vanity.
If the distance to the tailpiece is smaller, cut the tailpiece hook with the pipe opening with a hacksaw. If the distance is greater, you may have to replace the hook with a longer one.
Unscrew the nut from the sink of the P-trap, and plumbing it and the plastic washer inside. Slide the nut up along the hook and fit the washer around the end of the tailpiece. Set the P-trap opening against the washer and push up until the trap outlet is level with the waste pipe. Slide the nut down and screw it to the trap, tightening it as much as you can by hand.This Old House plumbing and heating expert Richard Trethewey shows how to install kitchen sink plumbing for a double-bowl sink.
In this video, This Old House plumbing and heating expert Richard Trethewey shows how to plumb a double-bowl sink. Turn off the water to the sink cabinet and plumbing the cabinet doors for easier access. Attach a shut-off valve to a length of copper tubing. Tighten the compressing fitting using two adjustable wrenches.
Repeat to make a second shut-off valve plumbing.
kitchen sink plumbing hook up - Home Improvement Stack Exchange
Connect the shut-off valves to the hot- and cold-water supply lines inside the sink cabinet. Confirm that the valves are off, then turn the water back on. Install the faucet spout and faucet handles to the countertop. Carefully tighten each threaded connection with an adjustable hook. Set the sinks into the drain holes in the bottom of each sink, then tighten from below with a wrench.
Scrape away any excess putty from inside the sinks. Connect a hook tailpiece to the sink of each plumbing strainer. Dry-assemble the ABS drainpipe and trap.