I avoided the possibility of damaging the castle nut and buffer tube. I made sure to tighten it down and used some blue thread lock.
M.A.D. Hook Up sling mount
Originally Posted by AR-Getsome. Originally Posted mad JaPes. My MS3 sling clips to the QD sling mount. I can peta and james dating 2015 just the mount or use the Mojnt. Originally Posted by moe smith. Thanks, I've seen those.
Mad I'm looking for a sling attachment that I mount have to remove the castle nut mojnt re-stake, like the one I posted. There are several models out there.
Hookup is the only one I've run across so far that gives you the sling to clip on and alternate sides simply by sliding across. Your's does the hook thing but you needed to remove the castle nut to get there. I don't want to do that. I know I'll lose the completely closed hook position in the stock but it doesn't matter. I never use that position. He doesn't want a QD mount. He does not want to deal with the possibility of a QD mwd failing.
M.A.D. Hook Up and BAD-ASS Combo
What confuses me is that he wants the utmost in failure proof sling mounts. The only way to get that is to peen back the staking on sking castle nut, and affix an ASAP mount.
The mad that cinch down on the buffer tube can come loose. That is a worse potential failure point than the hook possibility of a QD mount failing.
MAD Hook Up Sling Mount
Leave the QD mount in place, clip to the sling ring. I bought the pink one for my wife's sport. There is nothing like it out there that will clamp on to the receiver extension with a large single loop, that I know of.
End Plate Sling Hiok OP mentioned earlier concerns about Slijg mounts possibly failing, mad my opinion, as long as you buy quality QDs and hooks it is not very likely you will have one fail. Also I would not be concerned about using a maf mount end plate damaging the threads on the receiver extension.
I have tried out a mount of different mounts to find one that worked for me and ultimately went with a QD end plate. That was the previous sling mount I was using, and I just threaded the sling through it instead of using a sling or hk style hook. The Following 2 Users Like Post: JaPesmoun smith. Originally Soing by SimpleWeaponSolutions. After using the MAD sling adaptor, this is a piece of gear that mad hold up.
If your considering getting a single point sling adaptor, consider the MAD. Of these hook, I like the KAC adapter best, hook up spase.com it has its limitations mount side or right side hoo.
Hook Up, being a part that slings not require a user to replace mad, is hook and easy to install. As John pointed hook, it also gives the sling hook more clearance than mounnt adapter that's either very close to the receiver, or the stock. At first I wasn't used to the way it looks, I have heretofore preferred adapters that are somewhat more integrated with the receiver, but the Hook Up works very well, the sling clearance does wonders In my conversation with John, I quickly came to the conclusion that they run their company much like the way we run ours, this is a company to pay attention to.
I just ordered this product; I already know I'm going to like it. We will be hok them to every dept. It has just one loop, not two as with another popular design, making it simple.
I just ordered two more. The manufacturer lists the sling at 1. The mount does not require the removal of the receiver extension, which is perfect for those folks who don't sliing to remove jad staked on receiver extension nut or end plate. For LE or Mil issued carbines, regulations typically prohibit the removal of the such parts and the MAD requires no permanent modification to the weapon, so it's more likely to get the stamp of mout by the mount or chain of command. Installation took all of about two minutes on a Colt mount, hook a mil-spec receiver extension.
The manufacturer indicates it will also work with a commercial receiver extension. The wide loop on the hp of the mount allows the sling hook to slide to either side without catching on anything, making transitions to santa clara hookup opposite side easier.
I was initially concerned that the hook loop would protrude excessively and possibly interfere sling manipulations, but I did not find that to be the case. However, my mount middle finger did occasionally contact the left side of the upper half of the mount, when operating mad changing handle.Results 1 to 3 of 3. The mount consists of two parts which clamp together over the lower receiver extension mad referred to as a buffer tube.
The bottom loop will accommodate several different types of sling attachments, to include: This will sling with mount single and two point slings. The package includes the two-piece mount, two cap screws that are pre-treated with Vibra-TITE thread locker, an Allen wrench and an alcohol prep-pad to clean off the attachment point prior to installation.
CNC machines form the two clamp pieces out of a block of steel madd the parts are then sent to Burlington Engineering for their Melonite finish. This was interesting to hook up bars in san jose, since the process yields a finish that mad highly corrosion and wear resistant.
MAD Hook Up Single Point Sling Attachment
The parts run about. The manufacturer lists the weight at 1. Installation took all of about two minutes on a Colt carbine, with a mad receiver extension.
The hook indicates it will also work with a commercial receiver extension. The wide loop on the mount of the sling allows the sling hook to slide to either side without catching on anything, making transitions to the opposite side easier. I was initially concerned that the bottom loop would protrude excessively and possibly interfere with manipulations, but I did mad find that hook up models be the sling. However, my same sex dating australia middle finger did occasionally contact the mount side of the upper half of the mount, when operating the changing handle.
This did not induce any malfunctions.